GoranXS650's Photobucket media

Todd Moffat at Moffat Design & Spray in Wainuiomata did a Fantastic Paint Job. A Real Pleasure to deal with! He can be contacted on 027-458 96 05.

GoranXS650 — Mon, 24 Dec 2007 22:15:27 MST

GoranXS650 posted a photo

Todd Moffat at Moffat Design & Spray in Wainuiomata did a Fantastic Paint Job. A Real Pleasure to deal with! He can be contacted on 027-458 96 05. - 2007-12-24PaintWork01.jpg

Fuel Line Balance Pipe Installed.

GoranXS650 — Mon, 26 Nov 2007 02:02:55 MST

GoranXS650 posted a photo

Fuel Line Balance Pipe Installed. - 2007-11-26FuelLineBalancePipe03.jpg

Fuel Line Balance Pipe Installed.

GoranXS650 — Mon, 26 Nov 2007 02:02:34 MST

GoranXS650 posted a photo

Fuel Line Balance Pipe Installed. - 2007-11-26FuelLineBalancePipe02.jpg

Drawing of Fuel Line Balance Pipe.

GoranXS650 — Mon, 26 Nov 2007 01:14:50 MST

GoranXS650 posted a photo

Drawing of Fuel Line Balance Pipe. - 2007-11-27FuelLineBalancePipe.jpg

Fuel Line Balance Pipe Installed.

GoranXS650 — Mon, 26 Nov 2007 01:02:02 MST

GoranXS650 posted a photo

Fuel Line Balance Pipe Installed. - 2007-11-26FuelBalancePipe01.jpg

Drawing of Mikuni VM34 Mounting Rod

GoranXS650 — Mon, 26 Nov 2007 01:01:43 MST

GoranXS650 posted a photo

Drawing of Mikuni VM34 Mounting Rod - 2007-10-22MikuniVM34MountingRod.jpg

Carburettor Cables from Venhill.

GoranXS650 — Sun, 25 Nov 2007 03:49:50 MST

GoranXS650 posted a photo

Carburettor Cables from Venhill. - 2007-10-27ThrottleCable09.jpg

Cable Junction from Barnett.

GoranXS650 — Sun, 25 Nov 2007 03:49:34 MST

GoranXS650 posted a photo

Cable Junction from Barnett. - 2007-10-27ThrottleCable08.jpg

Throttle Handle from Motion Pro.

GoranXS650 — Sun, 25 Nov 2007 03:49:19 MST

GoranXS650 posted a photo

Throttle Handle from Motion Pro. - 2007-10-27ThrottleCable07.jpg

Ready for Installation.

GoranXS650 — Sun, 25 Nov 2007 03:49:00 MST

GoranXS650 posted a photo

Ready for Installation. - 2007-10-27ThrottleCable06.jpg

Silicone Grease used in the Cable Junction.

GoranXS650 — Sun, 25 Nov 2007 03:48:36 MST

GoranXS650 posted a photo

Silicone Grease used in the Cable Junction. - 2007-10-27ThrottleCable05.jpg

Slim Line Cable Junction from Barnett.

GoranXS650 — Sun, 25 Nov 2007 03:48:14 MST

GoranXS650 posted a photo

Slim Line Cable Junction from Barnett. - 2007-10-27ThrottleCable04.jpg

Throttle Cables Cut to Correct Lenght and Cable Nipples Soldered.

GoranXS650 — Sun, 25 Nov 2007 03:47:58 MST

GoranXS650 posted a photo

Throttle Cables Cut to Correct Lenght and Cable Nipples Soldered. - 2007-10-27ThrottleCable03.jpg

Cable from Throttle Handle to Cable Junction.

GoranXS650 — Sun, 25 Nov 2007 03:47:36 MST

GoranXS650 posted a photo

Cable from Throttle Handle to Cable Junction. - 2007-10-27ThrottleCable02.jpg

Making Throttle Cable. Throttle Handle and Main Throttle Cable from Motion Pro, Cable Junction from Barnett, Carburettor Cables from Venhill.

GoranXS650 — Sun, 25 Nov 2007 03:47:18 MST

GoranXS650 posted a photo

Making Throttle Cable. Throttle Handle and Main Throttle Cable from Motion Pro, Cable Junction from Barnett, Carburettor Cables from Venhill. - 2007-10-27ThrottleCable01.jpg

Close-Up of Mounting Rod.

GoranXS650 — Sun, 25 Nov 2007 03:13:26 MST

GoranXS650 posted a photo

Close-Up of Mounting Rod. - 2007-10-21MikuniVM3402.jpg

Mikuni VM34 and Manifolds Supplied by 650 Central. Note Mounting Rod between the Carburettors for Stability.

GoranXS650 — Sun, 25 Nov 2007 03:13:03 MST

GoranXS650 posted a photo

Mikuni VM34 and Manifolds Supplied by 650 Central. Note Mounting Rod between the Carburettors for Stability. - 2007-10-21MikuniVM3401.jpg

Fuel Line Balance Pipe to bolted with the P-Clips to the Battery Box Mounting Brackets..

GoranXS650 — Sun, 25 Nov 2007 02:53:50 MST

GoranXS650 posted a photo

Fuel Line Balance Pipe to bolted with the P-Clips to the Battery Box Mounting Brackets.. - 2007-11-25FuelBalancePipe02.jpg

Fuel Line Balance Pipe made from Solid Brass Shaft and Industrial Brass Fittings.

GoranXS650 — Sun, 25 Nov 2007 02:53:38 MST

GoranXS650 posted a photo

Fuel Line Balance Pipe made from Solid Brass Shaft and Industrial Brass Fittings. - 2007-11-25FuelBalancePipe01.jpg

The Rotor has been coated with a thin layer of Black Zinc. Ready for Installation.

GoranXS650 — Mon, 22 Oct 2007 03:18:31 MDT

GoranXS650 posted a photo

The Rotor has been coated with a thin layer of Black Zinc. Ready for Installation. - 2007-10-18Ignition01.jpg

High Quality Glass Filled Terminals with Stainless Steel Wire Protectors used together with Cable Ferrules.

GoranXS650 — Sun, 21 Oct 2007 15:39:05 MDT

GoranXS650 posted a photo

High Quality Glass Filled Terminals with Stainless Steel Wire Protectors used together with Cable Ferrules. - 2007-10-22Wiring02.jpg

P-Clips used to keep the Alternator Cable secured.

GoranXS650 — Sun, 21 Oct 2007 15:38:43 MDT

GoranXS650 posted a photo

P-Clips used to keep the Alternator Cable secured. - 2007-10-22Wiring01.jpg

Rubber Seals on Outer Cylinder Bolts replaced with Copper Washers from Suzuki. Part No: 09168-10017 (Gasket 10.5 x 22 x 2.3).

GoranXS650 — Sun, 21 Oct 2007 04:09:04 MDT

GoranXS650 posted a photo

Rubber Seals on Outer Cylinder Bolts replaced with Copper Washers from Suzuki. Part No: 09168-10017 (Gasket 10.5 x 22 x 2.3). - 2007-10-21Engine06.jpg

Stabilising Rod between the VM34 Mikunis. Note Modified Crank Case Breather.

GoranXS650 — Sun, 21 Oct 2007 04:08:23 MDT

GoranXS650 posted a photo

Stabilising Rod between the VM34 Mikunis. Note Modified Crank Case Breather. - 2007-10-21Engine05.jpg

Mikuni VM34 and Manifolds from 650 Central. K&N RC-1250 Air Filters.

GoranXS650 — Sun, 21 Oct 2007 04:07:59 MDT

GoranXS650 posted a photo

Mikuni VM34 and Manifolds from 650 Central. K&N RC-1250 Air Filters. - 2007-10-21Engine04.jpg

Rebuild Engine Ready For Installation.

GoranXS650 — Sun, 21 Oct 2007 04:07:36 MDT

GoranXS650 posted a photo

Rebuild Engine Ready For Installation. - 2007-10-21Engine03.jpg

Rebuild Engine Ready For Installation.

GoranXS650 — Sun, 21 Oct 2007 03:47:55 MDT

GoranXS650 posted a photo

Rebuild Engine Ready For Installation. - 2007-10-21Engine02.jpg

Rebuild Engine Ready For Installation.

GoranXS650 — Sun, 21 Oct 2007 03:46:26 MDT

GoranXS650 posted a photo

Rebuild Engine Ready For Installation. - 2007-10-21Engine01.jpg

Main Shaft Seal Kit Installed.

GoranXS650 — Sun, 21 Oct 2007 03:22:54 MDT

GoranXS650 posted a photo

Main Shaft Seal Kit Installed. - 2007-10-20SealKit04.jpg

Crank Shaft Seal Kit Installed.

GoranXS650 — Sun, 21 Oct 2007 03:22:36 MDT

GoranXS650 posted a photo

Crank Shaft Seal Kit Installed. - 2007-10-20SealKit03.jpg

Clutch Rod Seal Kit Installed.

GoranXS650 — Sun, 21 Oct 2007 03:22:23 MDT

GoranXS650 posted a photo

Clutch Rod Seal Kit Installed. - 2007-10-20SealKit02.jpg

Oil Seal Kit from Lance Stewart at Billroy Engineering NSW Australia Installed. This kit makes Future Seal Replacement possible Without Splitting the Cases.

GoranXS650 — Sun, 21 Oct 2007 03:22:00 MDT

GoranXS650 posted a photo

Oil Seal Kit from Lance Stewart at Billroy Engineering NSW Australia Installed. This kit makes Future Seal Replacement possible Without Splitting the Cases. - 2007-10-20SealKit01.jpg

Replacement Clutch Rod Seal Kit. Standard seal shown above.

GoranXS650 — Sun, 21 Oct 2007 03:16:55 MDT

GoranXS650 posted a photo

Replacement Clutch Rod Seal Kit. Standard seal shown above. - 2007-04-12SealKit04.jpg

Replacement Main Shaft Seal Kit. Standard seal shown above.

GoranXS650 — Sun, 21 Oct 2007 03:16:31 MDT

GoranXS650 posted a photo

Replacement Main Shaft Seal Kit. Standard seal shown above. - 2007-04-12SealKit03.jpg

Replacement Crank Shaft Seal Kit with Viton High Temperature Seal. Standard seal shown above.

GoranXS650 — Sun, 21 Oct 2007 03:16:09 MDT

GoranXS650 posted a photo

Replacement Crank Shaft Seal Kit with Viton High Temperature Seal. Standard seal shown above. - 2007-04-12SealKit02.jpg

Oil Seal Kit from Lance Stewart at Billroy Engineering NSW Australia. This kit makes Future Seal Replacement possible Without Splitting the Cases. Lance can be contacted on: bbillroy@bigpond.net.au

GoranXS650 — Sun, 21 Oct 2007 03:15:07 MDT

GoranXS650 posted a photo

Oil Seal Kit from Lance Stewart at Billroy Engineering NSW Australia. This kit makes Future Seal Replacement possible Without Splitting the Cases. Lance can be contacted on: bbillroy@bigpond.net.au - 2007-04-12SealKit01.jpg

The Rotor has been Machined to avoid the Magnets to hit the Pick-Up Pins. Machined by John Saywell - Keppel Engineering.

GoranXS650 — Thu, 18 Oct 2007 03:45:38 MDT

GoranXS650 posted a photo

The Rotor has been Machined to avoid the Magnets to hit the Pick-Up Pins. Machined by John Saywell - Keppel Engineering. - 2007-10-17Ignition01.jpg

Front Disc Universal Drill Pattern. 6mm Holes, 4 Deg Separation. Print Out and Make Your Own Drill Pattern.

GoranXS650 — Mon, 15 Oct 2007 03:49:02 MDT

GoranXS650 posted a photo

Front Disc Universal Drill Pattern. 6mm Holes, 4 Deg Separation. Print Out and Make Your Own Drill Pattern. - FrontBrakeDiscUniversal6mm-4Deg.jpg

Rear Disc Universal Drill Pattern. 6mm Holes, 4 Deg Separation. Print Out and Make Your Own Drill Pattern.

GoranXS650 — Mon, 15 Oct 2007 03:48:18 MDT

GoranXS650 posted a photo

Rear Disc Universal Drill Pattern. 6mm Holes, 4 Deg Separation. Print Out and Make Your Own Drill Pattern. - RearBrakeDiscUniversal6mm-4Deg.jpg

Front Disc Classic Drill Pattern. 90 of 8mm Holes.

GoranXS650 — Mon, 15 Oct 2007 00:02:26 MDT

GoranXS650 posted a photo

Front Disc Classic Drill Pattern. 90 of 8mm Holes. - FrontBrakeDisc90-8mmHoles-Straight.jpg

Rear Disc Classic Drill Pattern. 90 of 8mm Holes.

GoranXS650 — Mon, 15 Oct 2007 00:02:04 MDT

GoranXS650 posted a photo

Rear Disc Classic Drill Pattern. 90 of 8mm Holes. - RearBrakeDisc90-8mmHoles-Straight.jpg

Rear Disc Universal Drill Pattern. 10mm Holes, 6 Deg Separation. Print Out and Make Your Own Drill Pattern.

GoranXS650 — Sun, 14 Oct 2007 23:55:18 MDT

GoranXS650 posted a photo

Rear Disc Universal Drill Pattern. 10mm Holes, 6 Deg Separation. Print Out and Make Your Own Drill Pattern. - RearBrakeDiscUniversal10mm-6Deg.jpg

Rear Disc Universal Drill Pattern. 8mm Holes, 5 Deg Separation. Print Out and Make Your Own Drill Pattern.

GoranXS650 — Sun, 14 Oct 2007 23:43:06 MDT

GoranXS650 posted a photo

Rear Disc Universal Drill Pattern. 8mm Holes, 5 Deg Separation. Print Out and Make Your Own Drill Pattern. - RearBrakeDiscUniversal8mm-5Deg.jpg

Front Disc Universal Drill Pattern. 10mm Holes, 6 Deg Separation. Print Out and Make Your Own Drill Pattern.

GoranXS650 — Sun, 14 Oct 2007 23:41:12 MDT

GoranXS650 posted a photo

Front Disc Universal Drill Pattern. 10mm Holes, 6 Deg Separation. Print Out and Make Your Own Drill Pattern. - FrontBrakeDiscUniversal10mm-6Deg.jpg

Front Disc Universal Drill Pattern. 8mm Holes, 5 Deg Separation. Print Out and Make Your Own Drill Pattern.

GoranXS650 — Sun, 14 Oct 2007 23:40:39 MDT

GoranXS650 posted a photo

Front Disc Universal Drill Pattern. 8mm Holes, 5 Deg Separation. Print Out and Make Your Own Drill Pattern. - FrontBrakeDiscUniversal8mm-5Deg.jpg

New Made Stepped Aluminium Spacers are more stable and provides better support for the Pick-Up Circuit Board.

GoranXS650 — Thu, 11 Oct 2007 03:44:30 MDT

GoranXS650 posted a photo

New Made Stepped Aluminium Spacers are more stable and provides better support for the Pick-Up Circuit Board. - 2007-10-11Ignition09.jpg

Supplied Aluminium Spacers tend to Tilt when the screw is tighten. This can cause the Pick-Up Circuit Board to Deform.

GoranXS650 — Thu, 11 Oct 2007 03:44:21 MDT

GoranXS650 posted a photo

Supplied Aluminium Spacers tend to Tilt when the screw is tighten. This can cause the Pick-Up Circuit Board to Deform. - 2007-10-11Ignition08.jpg

Supplied Aluminium Spacers Replaced with New Made Stepped Aluminium Spacers. Machined by John Saywell - Keppel Engineering.

GoranXS650 — Thu, 11 Oct 2007 03:44:12 MDT

GoranXS650 posted a photo

Supplied Aluminium Spacers Replaced with New Made Stepped Aluminium Spacers. Machined by John Saywell - Keppel Engineering. - 2007-10-11Ignition07.jpg

Pick-Up Circuit Board. Yamaha Original Cable Sleeve is used.

GoranXS650 — Thu, 11 Oct 2007 03:43:25 MDT

GoranXS650 posted a photo

Pick-Up Circuit Board. Yamaha Original Cable Sleeve is used. - 2007-10-11Ignition06.jpg

Complete Ignition Rod Assembly. The Rotor is fixed to the Rod with Loctite.

GoranXS650 — Thu, 11 Oct 2007 03:43:03 MDT

GoranXS650 posted a photo

Complete Ignition Rod Assembly. The Rotor is fixed to the Rod with Loctite. - 2007-10-11Ignition05.jpg

Holding Tool to be used when the Lock Nut is tighten on the opposite end of the rod.

GoranXS650 — Thu, 11 Oct 2007 03:42:39 MDT

GoranXS650 posted a photo

Holding Tool to be used when the Lock Nut is tighten on the opposite end of the rod. - 2007-10-11Ignition04.jpg

Holes Drilled in the Rotor for Holding Tool.

GoranXS650 — Thu, 11 Oct 2007 03:40:10 MDT

GoranXS650 posted a photo

Holes Drilled in the Rotor for Holding Tool. - 2007-10-11Ignition03.jpg

Supplied Threaded Rod Replaced with New Made S/S Rod. Machined by John Saywell - Keppel Engineering.

GoranXS650 — Thu, 11 Oct 2007 03:39:54 MDT

GoranXS650 posted a photo

Supplied Threaded Rod Replaced with New Made S/S Rod. Machined by John Saywell - Keppel Engineering. - 2007-10-11Ignition02.jpg

Supplied Mounting Kit vs Modified Mounting Kit

GoranXS650 — Thu, 11 Oct 2007 03:39:34 MDT

GoranXS650 posted a photo

Supplied Mounting Kit vs Modified Mounting Kit - 2007-10-11Ignition01.jpg

The Daytona Meters have LED Lights.

GoranXS650 — Mon, 1 Oct 2007 03:34:32 MDT

GoranXS650 posted a photo

The Daytona Meters have LED Lights. - 2007-10-01Wiring16.jpg

Meters from Daytona Japan.

GoranXS650 — Mon, 1 Oct 2007 03:34:19 MDT

GoranXS650 posted a photo

Meters from Daytona Japan. - 2007-10-01Wiring15.jpg

Head Lamp Assembly.

GoranXS650 — Mon, 1 Oct 2007 03:33:35 MDT

GoranXS650 posted a photo

Head Lamp Assembly. - 2007-10-01Wiring14.jpg

The Rear Brake Pressure Switch and Rectifier can be seen.

GoranXS650 — Mon, 1 Oct 2007 03:33:15 MDT

GoranXS650 posted a photo

The Rear Brake Pressure Switch and Rectifier can be seen. - 2007-10-01Wiring13.jpg

Ground Tab Terminals for Rear Indicators.

GoranXS650 — Mon, 1 Oct 2007 03:33:01 MDT

GoranXS650 posted a photo

Ground Tab Terminals for Rear Indicators. - 2007-10-01Wiring12.jpg

All Ground Terminals done with Cable. Note Ground Terminal for Boyer Bransden Ignition.

GoranXS650 — Mon, 1 Oct 2007 03:32:02 MDT

GoranXS650 posted a photo

All Ground Terminals done with Cable. Note Ground Terminal for Boyer Bransden Ignition. - 2007-10-01Wiring11.jpg

Battery Ground Terminals.

GoranXS650 — Mon, 1 Oct 2007 03:31:16 MDT

GoranXS650 posted a photo

Battery Ground Terminals. - 2007-10-01Wiring10.jpg

All In One Switch Assembly from Suzuki.

GoranXS650 — Mon, 1 Oct 2007 03:31:00 MDT

GoranXS650 posted a photo

All In One Switch Assembly from Suzuki. - 2007-10-01Wiring09.jpg

Horn.

GoranXS650 — Mon, 1 Oct 2007 03:29:00 MDT

GoranXS650 posted a photo

Horn. - 2007-10-01Wiring08.jpg

Cable Entrance to Head Lamp Bucket.

GoranXS650 — Mon, 1 Oct 2007 03:27:22 MDT

GoranXS650 posted a photo

Cable Entrance to Head Lamp Bucket. - 2007-10-01Wiring07.jpg

Boyer Bransden Ignition.

GoranXS650 — Mon, 1 Oct 2007 03:26:28 MDT

GoranXS650 posted a photo

Boyer Bransden Ignition. - 2007-10-01Wiring06.jpg

Cable Entrance to Head Lamp Bucket.

GoranXS650 — Mon, 1 Oct 2007 03:26:14 MDT

GoranXS650 posted a photo

Cable Entrance to Head Lamp Bucket. - 2007-10-01Wiring05.jpg

Indicator Relay and Additional Relay for Neutral / Indicator Warning Light.

GoranXS650 — Mon, 1 Oct 2007 03:25:56 MDT

GoranXS650 posted a photo

Indicator Relay and Additional Relay for Neutral / Indicator Warning Light. - 2007-10-01Wiring04.jpg

Bosch RE 57 Regulator. Battery Acid Catch Can to the Left.

GoranXS650 — Mon, 1 Oct 2007 03:22:28 MDT

GoranXS650 posted a photo

Bosch RE 57 Regulator. Battery Acid Catch Can to the Left. - 2007-10-01Wiring03.jpg

New Fuse Carrier. All Terminals have been Soldered and covered with Heat Shrink.

GoranXS650 — Mon, 1 Oct 2007 03:19:54 MDT

GoranXS650 posted a photo

New Fuse Carrier. All Terminals have been Soldered and covered with Heat Shrink. - 2007-10-01Wiring02.jpg

Battery Terminals. 2.5mm Cable as there is no electric start.

GoranXS650 — Mon, 1 Oct 2007 03:19:32 MDT

GoranXS650 posted a photo

Battery Terminals. 2.5mm Cable as there is no electric start. - 2007-10-01Wiring01.jpg

Rubber Boot Mounted, Ready for Installation.

GoranXS650 — Sat, 29 Sep 2007 20:35:58 MDT

GoranXS650 posted a photo

Rubber Boot Mounted, Ready for Installation. - 2007-09-30Wiring04.jpg

A Fibre Glass Mat used to Protect the Cables from rubbing against the Reflector and Mounting Screws.

GoranXS650 — Sat, 29 Sep 2007 20:29:29 MDT

GoranXS650 posted a photo

A Fibre Glass Mat used to Protect the Cables from rubbing against the Reflector and Mounting Screws. - 2007-09-30Wiring03.jpg

High Quality Glass Filled Terminals with Stainless Steel Wire Protectors used together with Cable Ferrules.

GoranXS650 — Sat, 29 Sep 2007 20:29:18 MDT

GoranXS650 posted a photo

High Quality Glass Filled Terminals with Stainless Steel Wire Protectors used together with Cable Ferrules. - 2007-09-30Wiring02.jpg

All Connections Completed.

GoranXS650 — Sat, 29 Sep 2007 20:29:07 MDT

GoranXS650 posted a photo

All Connections Completed. - 2007-09-30Wiring01.jpg

Side Covers ready for Priming.

GoranXS650 — Wed, 26 Sep 2007 03:28:42 MDT

GoranXS650 posted a photo

Side Covers ready for Priming. - 2007-09-17SideCovers03.jpg

The Side Covers have been treated with POR 15 Metal Ready after Bead Blasting.

GoranXS650 — Wed, 26 Sep 2007 03:28:18 MDT

GoranXS650 posted a photo

The Side Covers have been treated with POR 15 Metal Ready after Bead Blasting. - 2007-09-17SideCovers02.jpg

The Air Filter Cut Out on the Side Covers have been modified for VM Mikunis with K&N RC-1250 Pod Filters.

GoranXS650 — Wed, 26 Sep 2007 03:24:18 MDT

GoranXS650 posted a photo

The Air Filter Cut Out on the Side Covers have been modified for VM Mikunis with K&N RC-1250 Pod Filters. - 2007-09-17SideCovers01.jpg

All cables are now in the Head Lamp Bucket ready to be connected.

GoranXS650 — Wed, 26 Sep 2007 03:09:49 MDT

GoranXS650 posted a photo

All cables are now in the Head Lamp Bucket ready to be connected. - 2007-09-26Wiring01.jpg

Clutch Cover Ready for Installation.

GoranXS650 — Sat, 8 Sep 2007 00:50:00 MDT

GoranXS650 posted a photo

Clutch Cover Ready for Installation. - 2007-09-08OilPump15.jpg

The Tachometer Drive Gear Shaft is installed. Note the Washer at the end.

GoranXS650 — Sat, 8 Sep 2007 00:49:50 MDT

GoranXS650 posted a photo

The Tachometer Drive Gear Shaft is installed. Note the Washer at the end. - 2007-09-08OilPump14.jpg

Oil Pump Installation Completed.

GoranXS650 — Sat, 8 Sep 2007 00:49:39 MDT

GoranXS650 posted a photo

Oil Pump Installation Completed. - 2007-09-08OilPump13.jpg

Tacho Drive Gear Installed. A piece of Aluminium is used to lock the Drive Gear when doing up the nut. I tend to use Loktite 222 Thread Locker here as well.

GoranXS650 — Sat, 8 Sep 2007 00:48:58 MDT

GoranXS650 posted a photo

Tacho Drive Gear Installed. A piece of Aluminium is used to lock the Drive Gear when doing up the nut. I tend to use Loktite 222 Thread Locker here as well. - 2007-09-08OilPump12.jpg

Pump Drive Gear Installed with Woodruff Key.

GoranXS650 — Sat, 8 Sep 2007 00:48:50 MDT

GoranXS650 posted a photo

Pump Drive Gear Installed with Woodruff Key. - 2007-09-08OilPump11.jpg

Back of Pump Drive Gear.

GoranXS650 — Sat, 8 Sep 2007 00:48:40 MDT

GoranXS650 posted a photo

Back of Pump Drive Gear. - 2007-09-08OilPump10.jpg

Oil Pump Installed with New Socket Cap Screws. I tend to use Loctite 222 Thread Locker here.

GoranXS650 — Sat, 8 Sep 2007 00:47:18 MDT

GoranXS650 posted a photo

Oil Pump Installed with New Socket Cap Screws. I tend to use Loctite 222 Thread Locker here. - 2007-09-08OilPump09.jpg

Pump Surface Checked for Damage.

GoranXS650 — Sat, 8 Sep 2007 00:47:10 MDT

GoranXS650 posted a photo

Pump Surface Checked for Damage. - 2007-09-08OilPump08.jpg

Clutch Cover Cleaned.

GoranXS650 — Sat, 8 Sep 2007 00:46:59 MDT

GoranXS650 posted a photo

Clutch Cover Cleaned. - 2007-09-08OilPump07.jpg

Note Markings on the Matched Rotor Assembly to ensure that they are installed facing the same direction.

GoranXS650 — Sat, 8 Sep 2007 00:45:43 MDT

GoranXS650 posted a photo

Note Markings on the Matched Rotor Assembly to ensure that they are installed facing the same direction. - 2007-09-08OilPump06.jpg

Oil Pump Cleaned and Ready for Assembly.

GoranXS650 — Sat, 8 Sep 2007 00:43:26 MDT

GoranXS650 posted a photo

Oil Pump Cleaned and Ready for Assembly. - 2007-09-08OilPump05.jpg

A Fine 6 x 100mm Round Slip Stone is used to De-Burr the raw edges of the new Oil Pump Rotor Assembly.

GoranXS650 — Sat, 8 Sep 2007 00:43:19 MDT

GoranXS650 posted a photo

A Fine 6 x 100mm Round Slip Stone is used to De-Burr the raw edges of the new Oil Pump Rotor Assembly. - 2007-09-08OilPump04.jpg

New Oil Pump Rotor Assembly from Yamaha.

GoranXS650 — Sat, 8 Sep 2007 00:43:06 MDT

GoranXS650 posted a photo

New Oil Pump Rotor Assembly from Yamaha. - 2007-09-08OilPump03.jpg

Selected Parts to be used.

GoranXS650 — Sat, 8 Sep 2007 00:39:52 MDT

GoranXS650 posted a photo

Selected Parts to be used. - 2007-09-08OilPump02.jpg

Oil Pump Covers and Pump Shafts tolerances are checked.

GoranXS650 — Sat, 8 Sep 2007 00:39:40 MDT

GoranXS650 posted a photo

Oil Pump Covers and Pump Shafts tolerances are checked. - 2007-09-08OilPump01.jpg

USA

GoranXS650 — Fri, 7 Sep 2007 04:29:48 MDT

GoranXS650 posted a photo

USA - UnitedStates.gif

UK

GoranXS650 — Fri, 7 Sep 2007 04:29:44 MDT

GoranXS650 posted a photo

UK - UnitedKingdom.gif

Classic Bike UK December 1996 Page 105

GoranXS650 — Fri, 7 Sep 2007 01:30:23 MDT

GoranXS650 posted a photo

Classic Bike UK December 1996 Page 105 - RubberXS650Page105.jpg

Classic Bike UK December 1996 Page 104

GoranXS650 — Fri, 7 Sep 2007 01:25:46 MDT

GoranXS650 posted a photo

Classic Bike UK December 1996 Page 104 - RubberXS650Page104.jpg

Classic Bike UK December 1996 Page 103

GoranXS650 — Fri, 7 Sep 2007 01:17:50 MDT

GoranXS650 posted a photo

Classic Bike UK December 1996 Page 103 - RubberXS650Page103.jpg

Classic Bike UK December 1996 Page 102

GoranXS650 — Fri, 7 Sep 2007 01:13:40 MDT

GoranXS650 posted a photo

Classic Bike UK December 1996 Page 102 - RubberXS650Page102.jpg

Classic Bike UK December 1996. Article: Rubber Yam XS650. Text: Mick Duckworth. Pictures: Richard Richards

GoranXS650 — Fri, 7 Sep 2007 00:45:07 MDT

GoranXS650 posted a photo

Classic Bike UK December 1996. Article: Rubber Yam XS650. Text: Mick Duckworth. Pictures: Richard Richards - RubberXS650Page00.jpg